 |
» |
|
|
|
 |
Special Note |
This course is appropriate for the following presses:
- HP Indigo press 1000
- HP Indigo press s2000
- Indigo TurboStream
- Indigo MultiStream
- Indigo Platinum
- Indigo e-Print Pro
|
Course Overview |
The shared support training program is a hands on course. The course focuses on the operation and interaction of the mechanical, electronic, fluid and substrate transport systems on the HP Indigo press. Participants will be taught how to apply maintenance skills to resolve problems. This may include preventative and/or corrective actions, or problem escalation through the Customer Support organization.
Audience
Qualified hp indigo digital press operators who will be required to perform service routines that include preventative maintenance, troubleshooting, and corrective maintenance
Prerequisites
A person who meets requirements for the Shared Support course has a background of
- Performing preventative and corrective maintenance on complex electromechanical devices.
- Has experience using electronic test equipment.
- Has successfully completed the operator training program for the hp indigo press 1000.
- Has a minimum of three months experience operating the hp indigo press 1000.
Benefits
Attendees will be taught techniques to optimize print quality, increase press uptime, and press availability
- Service contract terms tailored to shared support customer
- Access to technical phone support
Objectives
At the completion of this course you will be able to
- Understand of operation and interaction the major subassemblies
- Troubleshoot and repair basic electrical problems.
- Troubleshoot and repair mechanical sub systems.
- Properly observe safety precautions to diagnose problems and perform repairs.
- Be able to perform mandatory preventive maintenance functions at prescribed intervals.
- Perform a system back-up
- competently maintain the press and minimize service calls
Course outline
Introductions & Demonstrations
- Course Objectives
- Documentation
- Machine Introduction
- Safety & Disposal Procedures
- Introduction to Electrical Properties
- Digital Volt Meter Instruction
- Front Electronics Compartment
- Rear Electronics Compartment
- Identify Replaceable Electronic Boards
- Identify Cable Part Numbers
- Manual Operation of HVPS
Latent Image
- Scorotron-PIP Gap Adjustment
- PIP/Electrometer Clearance Adjustments
- Electrometer Board Calibrations
Writing Head
- Board Functions
- Writing Head Diagnostics
- Writing Head Adjustment Procedures
Ink System
- Density Calibration
- Conductivity Calibration
- Density Sensor Cleaning
- Ink Tank Replacement
- Dismantle Active Filter
- Ink Valves
- Slit Injectors Adjustments
- Delay and Duration Adjustments
Process
- Squeegee Bias Contact Replacement
- Reverse Rollers Bias Contacts Replacement
- Developer Drum Contact Replacement
- ITM Bias Carbon Brush Replacement
Drums Synchronization and Engagement Adjustments
- Remove and Replace ITM Drum (optional)
- Engage - Disengage Adjustment and Synchronization
- Drum Synchronization
- Adjusting 2nd Transfer Pressure
- Encoder Calibration
- ITM Sensor Adjustment
Separator
- Disassembling the Separator
- Cleaning the Separator
- Servicing the Separator
- Adjusting Imaging Oil Flow Rates
- Cleaning Station Adjustments
Paper Input
- Adjusting the Suction Fingers Travel Limits
- Adjusting the Paper Feed Rollers
- Adjusting the Sheet Separators and Side Blowers
- Testing and Adjusting Drum/Cam Synchronization
- Paper Transport Timing
Paper Output
- Testing and Adjusting Gripper Tension
- Testing and Adjusting the Gripper Solenoid
- Testing and Adjusting the Stripper Bar
Duplex System
- Replacing the Eject Roller Assembly
- Testing and Adjusting the Duplex Feed Cam
- Balancing the Duplex Tray Upper Feed Rollers
- Testing and Adjusting the Duplex Feed Solenoid
- Aligning the Paper Transport System
PIP Holder
- Adjusting PIP Foil Holder
Vacuum Pump
Solid Add Compressor
- Adjusting Solid Add Pressure
Computer
- Remove PC
- Identify PC Components
- Perform Config.Save
- Perform System Backup
Troubleshooting
- Schematics Overview
- Electrical & Mechanical Troubleshooting
**For prices in Pounds (£) please contact the UK
|
|
|
Printable version
